Share/Bookmark

Get one in LAZADA now!

Tuesday, November 11, 2014

Hard Reset: MyPhone Agua Rio Fun solutions







Model Number: MyPhone Agua Rio Fun
Android Version: 4.2.2
Build Number: ALPS.JB3.M.V1.P146
Custom build version: S5200AP_Agua_Rio_Fun_20140527_v1.17


CLICK BELOW
* Press vol up and vol down + power button

* Select recovery mode: Volume up
   it must display My|Phone logo + android logo with red interrogative sign like this (!)

* Press power button

*Select wipe data/factory reset by vol up and down

* Press list key to choose not home key

*choose yes by vol down

* Press list to execute

* Wiping data done!!

* and reboot by list key...My|Phone logo should display!!
JOB well done....then smile....

______________________________________________________
++Intended for MyPhone Rio Fun V2, with software version S5202Ap_KK_Agua_Rio_Fun_20140910_1.09++


Update: Although this firmware is intended for MyPhone Rio Fun V2, with software version S5202Ap_KK_Agua_Rio_Fun_20140910_1.09 (as shown in my photo that I took below) there's still a possibility that you might brick your phone. As I have said below, I only tried this firmware once with Privacy Password Lock problem. And the procedure that I use is below, and it worked for me. I am not really sure what happened to other MyPhone Rio Fun users that flashed this firmware.


!!!So please flash at your own risk.!!!



Update 2:  I was able to fixed another phone with this firmware. The problem of the phone was I was expanding the storage via Link2SD and I accidentally erased an important file. So what I did is I restored the back up via TWRP, but I cannot restore because of mismatch md5 checksum. So tweaked the back up files. And restore again. And BOOM! I bricked the phone. So my last resort was to flash this firmware. I also experience the 4% of death. I tried to firmware upgrade first and It successfully flashed but the phone is in boot loop state.So I flashed it again (Download Only) and it finally boot up properly...

This firmware is for MyPhone Agua Rio Fun V2 or board Version 2 for MTK6571. I have tried this firmware in a phone with Privacy Password.

Please follow my guide carefully, because you might brick your phone. You might experience the 4% of death when you are trying to flash your phone.

The firmware is not rooted. If you want to root this phone you can use Kingroot. 

The software version of this firmware is version 1.09. Please check your software version in factory mode (PRESS AND HOLD VOLUME UP + DOWN + POWER BUTTON) Then go to test item, then select the first item.




You can fix the following issue in your phone:
1. Bootloop
2. Damaged System UI
3. TP Upgrade only
4. Dead phone but it is detected in computer
5. Remove Gmail Account / Password / Pattern Lock (Alternative Way)
6. Privacy Protection Password Lock up

"DOWNLOAD THESE FILES" 
-------------------------------
-------------------------------Firmware Here -->MyPhone Agua Rio Fun Kitkat MTK6571

VCOM Driver -->VCOM Manual
Alternative Driver --> AutoInstaller
SPFlashTool --> LatestVersion 


"Use WinRar or 7zip to extract the firmware" 
"Extract the files to your desired folder" 
"If you encounter error in flashtool, use different version of it."



 "I suggest to use 32bit Windows OS for compatibility of the driver"



Installing Driver with AutoInstaller

First try the Alternative Driver, which is the AutoInstaller. Just open the install.exe then it will automatically install the driver. To fully check if the driver is correctly installed in your computer. 

Follow these steps:

  1. Turn off your phone (always powered off is a must)
  2. Press and hold volume up or down, or you can simple press the two button.
  3. Insert your USB cable without releasing the VOLUME button(s).
  4. In your computer, it must detect your phone and it will install the MTK Preloader or Mediatek USB VCOM driver.
  5. Repeat 1 to 4 if it does not detect your phone.
  6. If MTK Preloader/Mediatek USB VCOM Driver is installed you are good to go in flashing your phone ^_^

Reference Video using Driver Auto Installer (watch in HD)




Installing Manually using VCOM Driver
When installing it manually your phone must be turned off, then connect it to your computer/laptop while pressing VOLUME UP or VOLUME DOWN. This will detect and look for the driver.


 1. This is the first time that you will connect your phone and it will search for the correct driver.

2. Check include this location ... ... and click on browse. Look for USB VCOM Driver and Click on 2K_XP_COM folder if you are using Windows XP or Win7 for Windows 7 and then press OK when you are done picking the right folder for the driver.


3. If the driver is successfully installed MediaTek DA USB VCOM will appear in the New Hardware Wizard.

Video Installing VCOM Driver (please watch in HD)






"Your Phone must be turned off when you are ready to connect and flash your phone" 

Flashing
1. Launch FlashTool (flash_tool.exe)
2. In Flashtool, Click on Scatter-Loading, and load your scatter file. (see example below)

Reference Video Using FlashTool version 5.xxx (watch in HD)




 3. After you load the file, UNCHECK PRELOADER only, press Press Download to Flash your Phone.

4. After you press Download Follow these steps
  • Turn off your phone (always powered off is a must)
  • Press and HOLD volume UP or Down or you can simply press it simultaneously
  • Insert your USB cable without releasing the VOLUME button(s).
  • Keep on repeating until Flashtool detected your phone.
5. If successfully detected just wait until the progress bar reaches 100%. If your phone did not automatically turn on after flashing, remove battery and USB cable. And put back your battery then turn on your device.



"Hard reset your phone after flashing"



Some workarounds:
If you encounter PMT_Changed error here is what you do:
In Latest version of Flashtool

PMT_CHANGED error occur when firmware is not compatible with your phone. Sometimes your phone has a different board version. You should check it too, if your firmware is compatible with your phone.  

If you encounter Privacy Protection Password:

  1. Open flash_tool.exe
  2. Load the scatter file
  3. Goto Format Tab
  4. Click on Format except bootloader
  5. Press Play/Start Icon
  6. Then remove battery
  7. Insert the battery again
  8. Insert the USB cable (you should hear a beep on your computer, and it should proceed in formatting.)
  9. After done formatting proceed in Flashing.
  10. Goto Download tab (I assume that you loaded the scatter file already)
  11. Uncheck PRELOADER (this is very important)
  12. Press Download
  13. Then remove battery
  14. Insert Battery again
  15. Insert the USB cable (you should hear a beep on your computer, and it should proceed in flashing or downloading the firmware in your phone.)
  16. Power ON the phone after flashing.
  17. Restore your IMEI.


For Invalid IMEI:Your Phone/Tablet must be rooted first
Restore yong IMEI in MTKDroidTools version 2.5.3. You will have this error when you format your phone in Flashtool as I had experienced. To restore download MTKDroidTools version 2.5.3 After you extract the file. Open the green robot, you must enable the usb debugging in your phone. It is usually located in Settings>Devoloper Mode then look for usb debugging. After enabling it. Connect your phone in your computer then in MTKDroidTool click on ROOT. Wait for it to finish, then Click in IMEI/NVRAM, input 15 number in each box. Then click REPLACE. Then click Reboot or you can manually turn off your phone. Then turn your phone on again. You can see that you have fully restored your IMEI. 



 
FOR DAMAGED BASEBAND or UNKNOWN BASEBAND (Your phone must be rooted first)

1. Make sure you have MTKDROIDSTOOL version 2.4.8 or version 2.5.3 (you can search it in google)

2.  In MTKDroidstool (I assume you launch the tool) -- Click in Root. 
3. In your device -- After you press Root, you need to authorize it. A pop up message will appear. Click Allow/Authorize depends on your root application.
4. In MTKDroidsTool -- Click in IMEI/NVRAM, then click in RESTORE.
5. Then look for the folder where you extracted the NVRAM files.
6. Check if the Baseband is fixed. And if the IMEI is fully restored.
7. If Baseband is still Unknown and IMEI is invalid. Then you need to hard reset first your phone.
8. After hard reset your baseband should be fixed already. (base on my experience)
9. If your baseband is fixed sometimes the IMEI is still invalid. So you need to restore the IMEI.
10.  To restore IMEI follow Step 1-4, but you should not restore. You should fill the IMEI then click REPLACE. Then reboot your phone.  VOILA! I hope the phone is fully working :)

I hope this tutorial help you. Please drop a comment if something is not clear to you.

Tested by:
Me - Files / Flashing / Privacy Protection Password

I would like to give credits to those who uploaded the file online.

27 comments:

  1. Hello! Sinubukan ko na ng ilang beses mag boot into recovery mode pero ayaw tlga. Even press Ako ng press ng volume up ayaw pa din. Please help.. Gumamit na Ako ng ROM manager, link2sd, mobile uncle,. Rooted ang device ko. Please po help naman
    ..

    ReplyDelete
    Replies
    1. check mo yung battery level...if ok...hardware issue na yan miss..
      pero halos lahat ng ganitong model ay kaya ng hard reset procedure na ito...try again baka
      kulang lang sa timing...if not...hardware issue.

      Delete
    2. paki check din ng mga switches....basic lang muna bago pumunta sa mga ic's

      Delete
  2. 95% naman po sir ang battery level ko.. Kung hardware issues po, Ano po possible na sira ng cp ko? Ano po pinaka magandang gawin? Pasensya na po, new bie lang po Ako.. OK naman po sir ang mga switches nya.. Volume up and Down, power button.. Salamat po!

    ReplyDelete
  3. thank you sir... it work on my phone :)

    ReplyDelete
  4. Ganyan din phone ko, ayaw mag recovery mode. Parang namamatay lang. As in walang nangyayari.

    ReplyDelete
  5. basta sabay nyo lang Press vol up and vol down + power button
    kunting timing lang....paki share na rin din sa site...thanks...more power

    ReplyDelete
  6. hi! this one work on my phone but the problem is nawala lahat ng display icons sa phone as in pure black..pano ko po ibabalik ung mga icons ko.. thanks..

    ReplyDelete
    Replies
    1. pareho po tayu ung launcher po ung problem baka ubos na po ung memory nio


      Delete
  7. tama

    salamat sa admin nito ok na ulit cp q

    ReplyDelete
    Replies
    1. ok nga ya Edison Astada .... paki share naman tong blog nato...tnx

      Delete
  8. ok nga ya Edison Astada .... paki share naman tong blog nato...tnx

    ReplyDelete
  9. nakaka delete po ba ito ng system virus? myphone agua rio din yung cp ko..

    ReplyDelete
  10. ung cp ko po wala na pong space ung internal storage tapos ayaw ng gumana ng launcher nung nirestart ko po lumalabas lang po ung myphone na tatak wala na pong nangyayari....
    pano po yun? pls.. i need help

    ReplyDelete
  11. every time i press the up button di nakikita ung logo ng andriod kaya nag popop up po interupted

    ReplyDelete
  12. Pano po pag d gumana ayaw po talaga ano po ang dapat gawin?

    ReplyDelete
  13. boss na wipe ko na. pabalik balik parin ang my phone logo. help please. thanks...

    ReplyDelete
  14. meron po akong problema sir..sinubukan mag flash ng stock rom sir.. bootloop po kasi.. detected po sya sa PC nag i flash ko na.. nag error po "NAND FLASH ERROR" daw. pagkatapos ayaw na mag open. but detected padin sa PC.. then nag try ako ng ibang Firmware i mean download same name sa device.. ang ngyari... ayaw na ma detect... not recognize na po sya at minsan nlang ma detect.. and still ayaw padin ma open... may paraan paba pra mapa andar ko pa tong phone ko? kahit dun nlng sa my factory reset?

    ReplyDelete
  15. sir patulong po sa agua rio lite ko, naka stock lng po xa sa myphone logo pa inopen,sinubukan ko na hard reset pero pag lumabas na yung boot to recovery mode at pinili ko using volume up walang ngyayare,bumabalik lng sya sa logo..sana po me makatulung. thanks

    ReplyDelete
  16. hello po. ayaw po mag-select ng recovery mode ng phone ko. when i press volume up, namamatay po yung phone.

    ReplyDelete
  17. I encountered BROM error... so I tried to force format all.. then brick na lalo. wala na recovery mode,even charging doesnt show up... the phone was still detected but 3% lng sa flashing BROM na ulit... -rio V1...

    ReplyDelete
  18. Hello po.. Hindi ko po magamit CP ko kasi yong Touch Screen nya.. di ko mapindot. iba iba napipindot nya Automatically.. hayss.. pano po ito-?? Thank You

    ReplyDelete
  19. May iba pbang way pra mg open ung rio fun ko, kc it only displays my phone, hanggang dun lng, khit recovery mode ko sya.

    ReplyDelete
    Replies
    1. hi. pareho po ng nangyari sa phone ko yung sa iyo and if ever pwede po magtanong kung paano niyo po na-fix 'to. salamat

      Delete
  20. hellow gud murning myphone company bat po ganun running space poh na labas at ayaw ma open ng pin code,, tnx poh

    ReplyDelete
  21. hi. can i ask kung paano naman po kapag yung myphone lang po yung lumalabas then di na po nagtutuloy to open. ni-try ko na po yung factory reset but it didnt work. pls help me on how to fix it or ipapa-repair ko na lang 'to sa expert on this field. Salamat in advance

    ReplyDelete

Catch some quality Z’s this weekend with your #AndroidWear. The Sleep as Android app helps you fall asleep, stay asleep and wake up at the optimal time #WeekendWear https://goo.gl/PVkP7

Posted by Android on Saturday, May 30, 2015

pc cp technician forums